Microsonic hps+25/DD/TC/E/G1 User Manual download pdf









T1 + T2

Set detect distance in

mm or cm

For single detect

point press T2

until »- - -« is

displayed

Choose » « for NCC or

» « for NOC







For window mode

operation set far

detect point in

mm or cm

T1 + T2



Press T1 and T2 simultaneously for about

3 s until welcome message has passed

T1 + T2







T1 + T2



T1 + T2



T1 + T2









Set switched output D1

Set switched output D2

Ready

Start here

Set sensor parameters alternatively numerically using LED-display...









T1 + T2

Set detect distance in

mm or cm

Choose » « for NCC

or » « for NOC





T1 + T2







T1 + T2

For single detect

point press T2

until »- - -« is

displayed

For window mode

operation set far

detect point in

mm or cm



Product description

 The hps+ sensor measures the level in a

vessel in up to 6 bar overpressure contact-

less. The G1 and G2 threaded pipe end

permits the mounting and sealing of the

sensor in a flange of the vessel. The pnp

switched outputs are set according to the

adjusted detect distances.

 The surfaces of the ultrasonic tranducers

of the hps+ sensors are protected by a

PTFE film (Teflon film) and sealed with a

FFKM O-ring against the sensor housing.

Therefore the surface of the ultrasonic

transducer can be cleaned from cakings

or spots.

 All settings are done with two push-but-

tons and a three-digit LED- display

(TouchControl).

 Light emitting diodes (three-colour LEDs)

indicate all operation conditions.

 Choosing between output function NOC

and NCC is possible.

 The sensors are adjustable manually using

the numerical LED-display or may be trai-

ned using Teach-in processes.

 Useful additional functions are set in the

Add-on-menu.

 With the LinkControl- Adapter LCA-2,

available as accessory, all sensor settings

can be made optionally with a PC using

the LinkControl software.

Important instructions for assembly and ap-

plication

All employee and plant safety-relevant

measures must be taken prior to assembly,

start-up or maintenance work (see operation

manual for the entire plant and the operator

instruction of the plant).

The sensors are not considered as safety

equipment and may not be used to ensure

human or machine safety!

The hps+ sensors indicate a blind zone, in

which the distance cannot be measured. The

operating range indicates the distance of the

sensor that can be applied in normal atmos-

pheric preassure with sufficient function re-

serve.

Assembly instructions

► Assemble the sensor at the installation lo-

cation.

► If necessary seal the sensor with the en-

closed Viton O-ring (34 x 2,5 mm or 60 x 4

mm) against the flange.

► Plug in the connector cable to the M 12

connector.

Fig. 1: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

Start-up

hps+ sensors are delivered factory made with

the following settings:

 Switched outputs on NOC.

 Detecting distances at operating range

and half operating range.

colour

-U

brown

blue

black

white

Sync/Com. grey

 Measurement range set to maximum

range.

 Sensitivity at Normal preassure.

Set the parameters of the sensor manually or

use the Teach-in procedure to adjust the de-

tect points.

Fig. 2: TouchControl

Operation

hps+ sensors work maintenance free. Small

amounts of dirt on the surface do not influ-

ence function. Thick layers of dirt and caked-

on dirt affect the sensor function and there-

fore must be removed.

Note

 In operation in overpreassure it is reco-

mended to adjust the sensitivity of the

hps+ sensor: choose the parameter A14 in

the Add-on menu and set it to sensitivity

E2 for atmospheric preassure from 1 to 3

bar or to sensitivity E3 for atmospheric

preassure > 3 bar.

 hps+ sensors have internal temperature

compensation. Because the sensors heat

up on their own, the temperature com-

pensation reaches its optimum working

point after approx. 30 minutes of opera-

tion.

 During normal mode operation, a yellow

LED signals that the corresponding

switched output has connected.

 During normal mode operation, the mea-

sured distance value is displayed on the

LED-indicator in mm (up to 999 mm) or

cm (from 100 cm). Scale switches auto-

matically and is indicated by a point on

top of the digits.

 During Teach-in mode, the hysteresis

loops are set back to factory settings.

 If no objects are placed within the detec-

tion zone the LED-indicator shows »- - -«.

 If no push-buttons are pressed for 20 se-

conds during parameter setting mode the

made changes are stored and the sensor

returns to normal mode operation.

Show parameters

Tapping push-button T1 shortly during nor-

mal mode operation shows »PAr« on the

LED-display. Each time you tap push-button

T1 the actual settings of the analogue output

and the switched output are shown.

Instruction manual

hps+ Ultrasonic Sensors for appli-

cation in overpressure with two

switched outputs

m m

measuring range

LED D1 and D2

3-digit

LED-display

Push-buttons T1 and T2

hps+25/DD/TC/E/G1

hps+35/DD/TC/E/G1

hps+130/DD/TC/E/G1

hps+340/DD/TC/E/G2

hps+340/DD/TC/G2

2004/108/EC

1 2 3

Summary of Contents

Page 1 - Start here

T2T1T2T2T1T1 + T2Set detect distance inmm or cmFor single detectpoint press T2until »- - -« is displayedChoose » « for NCC or» « for NOCT1T2Fo

Page 2 - Key lock and factory setting

...or with the Teach-in procedureAdjust detect point D1Place object at position  Press T1 until »d« is shownCurrent measu-ring valuePress T1 until »

Page 3 - Technical data

*B8990* MV-DO-107940-267091Technical dataBlind zoneOperating rangeMaximum rangeAngle of beam spread0 to 30 mm 250 mm0 to 85 mm 350 mm990 mmPlease see

Related models: hps+35/DD/TC/E/G1 | hps+130/DD/TC/E/G1 | hps+340/DD/TC/E/G2 | hps+340/DD/TC/G2 | hps+25/DIU/TC/E/G1 | hps+35/DIU/TC/E/G1 | hps+130/DIU/TC/E/G1 | hps+340/DIU/TC/E/G2 | hps+340/DIU/TC/G2 |

Comments to this Manuals

No comments

Microsonic hps+25/DD/TC/E/G1 User Manual

Browse online or download User Manual for Sensors Microsonic hps+25/DD/TC/E/G1. Microsonic hps+25/DD/TC/E/G1 User Manual

Summary of Contents

Related models: hps+35/DD/TC/E/G1 | hps+130/DD/TC/E/G1 | hps+340/DD/TC/E/G2 | hps+340/DD/TC/G2 | hps+25/DIU/TC/E/G1 | hps+35/DIU/TC/E/G1 | hps+130/DIU/TC/E/G1 | hps+340/DIU/TC/E/G2 | hps+340/DIU/TC/G2 |

Comments to this Manuals

Related products and manuals for Sensors Microsonic hps+25/DD/TC/E/G1