Microsonic sks-15/D User Manual download pdf

Sensor adjustment with Teach-in procedure

Set detect point

Place object at position ➀

Press push-button for about

3 s until LEDs flash

simultaneously

both LEDs: flash

mutually

Press push-button for

about 1 s

Set window mode

Place object at position ➀

Press push-button for about

3 s until LEDs flash

simultaneously

both LEDs:

Place object at position ➁

Press push-button for

about 1 s

flash

mutually

Set two way reflective

barrier

Set NOC/NCC

Enable/disable Teach-in

push-button

Switch off power supply

Place reflector at position ➀

Press push-button for about

3 s until LEDs flash

simultaneously

Press button for about 13 s

until LEDs flash

mutually

both LEDs: flash

mutually

Press push-button for

about 10 s

green LED:

yellow LED:

To change output characte-

ristic press push-button

for about 1 s

While pressing the push-

button switch on power

supply

Keep push-button pressed

for about 3 s until both

LEDs flash simultaneously

flashes

on: NOC

off: NCC

green LED:

yellow LED:

flashes

on: push-button

enabled

off: push-button

disabled

To enable/disable Teach-in

press push-button

for about 1 s

Reset to factory setting

Switch off power supply

While pressing the push-

button switch on power

supply

Keep push-button pressed

for about 13 s until both

LEDs stop

flashing

Normal operating mode

Wait for 10 s Wait for 10 s

Normal operating mode

85 %

Operating Instructions

sks-15/D sks-15/E

sks-15/CD sks-15/CE

Ultrasonic proximity switch with

one switched output

Ultrasonic Sensors

Product Description

The sks sensor offers a non-contact

measurement of the distance to an

object which must be positioned

within the sensor’s detection zone.

The switched output is set in depen-

dence of the adjusted detect dis-

tance.

Via the push-button, the detect dis-

tance and operating mode can be

adjusted (teach-in). Two LEDs indi-

cate operation and the state of the

switched output.

The output function is changeable

from NOC to NCC.

Safety Notes

■ Read the operating instructions

prior to start-up.

■ Connection, installation and

adjustment works may only be

carried out by expert personnel.

■ No safety component in

accordance with the EU Machine

Directive

Proper use

sks ultrasonic sensors are used for

non-contact detection of objects.

Installation

■ Mount the sensor at the installa-

tion site.

Maximum torque: 0,5 Nm

■ Connect a connection cable to the

M8 device plug.

Fig. 2: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

3-pin initiator plug

colour

brown

4-pin initiator plug

-U

blue

black

colour

-U

brown

blue

Com

black

white

Start-Up

■ Connect the power supply.

■ Carry out the adjustment in

accordance with the diagram.

Factory Setting

■ Operation with one detect point

■ Switched output on NOC

■ Detect points at operating range

Operating modes

Three operating modes are available

for the switched output:

■ Operation with one detect point

The switched output is set if the ob-

ject falls below the set detect point.

■ Window mode

The switched output is set if the ob-

ject is within the set window mar-

gins.

■ Two-way reflective barrier

The switched output is set if the ob-

ject is between sensor and reflector.

Checking operation mode

■ In normal mode shortly press the

push-button.

The green LED stops shining for one

second, then it will show the current

operation mode:

1 x flashing = operation with one

switching point

2 x flashing = window mode

3 x flashing = reflective barrier

After a break of 3 s the green LED

shows the output function:

1 x flashing = NOC

2 x flashing = NCC

Maintenance

microsonic sensors are maintenance-

free. In case of excess caked-on dirt

we recommend cleaning the white

sensor surface

Notes

■ sks-15/CD and sks-15/CE sensors

have internal temperature com-

pensation. Because the sensors

heat up on their own, the tempe-

rature compensation reaches its

optimum working point after ap-

proximatly 30 minutes of operati-

on.

The sensors sks-15/D and sks-15/E

have no temperature compensati-

on.

■ The sks sensor has a blind zone,

within which distance measure-

ments are not possible.

■ In the normal operating mode, an il-

luminated yellow LED signals the

switched output is switched

through.

■ If the object to be sensed moves

into the detection area from the

side, the switching distance should

be set 8-10 % further than the de-

sired switch point to obtain a reli-

able object detection.

If the object moves towards the

sensor (e.g. level control) the de-

tect point can be taught to the ac-

tual distance at which the sensor

has to switch the output.

Set switched output

Further settings

1 2

Ultrasonic Sensors 1

Summary of Contents

Page 1 - Ultrasonic Sensors

Sensor adjustment with Teach-in procedureSet detect pointPlace object at position ➀Press push-button for about3 s until LEDs flash simultaneously both

Page 2

Technical dataBlind zoneOperating rangeMaximum rangeAngle of beam spread20 mm150 mm20 mm150 mm250 mmSee detection zone250 mmSee detection zoneTransduc

Related models: sks-15/CD | sks-15/E | sks-15/CE |

Comments to this Manuals

No comments

Microsonic sks-15/D User Manual

Browse online or download User Manual for Sensors Microsonic sks-15/D. Microsonic sks-15/D User Manual

Summary of Contents

Related models: sks-15/CD | sks-15/E | sks-15/CE |

Comments to this Manuals

Related products and manuals for Sensors Microsonic sks-15/D